Project: LED Brake light

Installed a new LED high mount brake light today. The unit is from Hella, and fits flush into the top of the tailgate.

The job took about 4 hours, with most of the time spent in cutting and filing the hole in the tailgate.


Full details of the installation can be found in my old holden shed.

Project: Recolouring Door Trims

As part of the on-going quest for a black interior, I needed to make a decision regarding the door trims. To replace, retrim or recolour?

I don't mind the vinyl trims - it's just the colour I'm not crazy about, so I decided to have a go at recolouring them.

Here's the door trim removed form the car:

Door trim before

Door Trim just after dyeing

I'm quite impressed with the overall finish, and the ease with which it can be done. I used a VHT Vinyl Dye, which soaks into the vinyl.


If you want full details on how this was done, click here to see my old holden shed.

One seat in

Well - I managed to get one of the new seats fitted into the van today.

The seat runners are totally different, and there are brackets welded onto the WB seats which can't be taken across to the new seats. Bummer.

HZ Seat Runners

WB Seat Runners

I managed to fabricate some adapter plates which allow me to use all of the original seat mounting holes in the floor pan, and the seat brackets which come with the HZ seats. I'm happy with the end result - the picture below shows the new seat in place, along side the old one.

Project: Carpet and Console

Time for a change - I'm not fond of the brown interior, so over the coming months everything will be changed over to black.

Brown Interior

I bought some carpet and underlay a while back from Tru-fit, and also bought a replacement centre console from American Autos. I decided that it was time to install the carpet and console.

Full details and photos of the project can be found by clicking here to visit my old holden shed.

The end result was very good, as you can see from the photo below.

New Carpet and Console

The next step is to find some new seats, or get the brown ones retrimmed.

Project: Statesman Front

Always liked the Statesman fronts on a van and ute, so it was time give the WB the treatment.

If you are planning on doing this, try and get a Caprice front as they are more highly sought after than the DeVille. The Caprice front has a nice grill (all metal) whereas the DeVille has a plastic job. You can't swap them over easily.

I picked up a full walk off front on eBay (again!) for $1100. The whole thing was in great condition, and was still attached to the rest of the car. We dismantled it ourselves, which meant that we could ensure nothing was damaged.

After getting the front home, I checked things out, and realised that even though the radiator support panels are similar, I need the Statesman one fitted to the van to hold the larger headlights.

The Statesman support panel was painted white, so I spent $190 at the local painters and got it blasted, and then painted in 2-pack black. End result was pretty good!


After that, it was a case of painting the nose panel, dismantling the existing front, and fitting the new pieces.

Very happy with the end result!

For the full details of what's involved, click here to visit my old holden shed!

A big thank you to Ed for helping me pick up and
transport the new walk off front.

Project: Adding Flashlube

Anyone who drives and older car knows that in some cases modern fuels can be harmful to the valve seats of your engine.

The solution to the problem is to add something to your unlead fuel to help with the upper cylinder lubrication. Easy if you run petrol, a bit harder if you run dual fuel. Enter the "Flashlube" kit.

This kit is hooked up to a vacuum line on the carb of your engine to "suck" through some of the special lubricant at a steady rate, which automagically mixes with the fuel.

Click here for more info on Flashlube, and what it does.

As the van didn't have any such kit installed, and I had no idea as to whether the heads had been upgraded for LPG and unleaded - I decided to add a kit. After all, the kit won't do any harm!

I picked one up on eBay (again!) for $35. A bargain. The kit arrived, was brand new, and it took a couple of hours to install.

The full kit

For full details on installation of the kit, click here to see the project details in my old holden shed.

Headlight Reminder

Because I'm getting older, and more forgetful, I decided to install a simple buzzer to act as a Headlight Reminder.

Not a difficult job, but it's saved me from a flat battery more than once.

The unit was a very low cost item I picked up at an electronics store, and it took me about an hour to wire it in.

Click here to see the full details of the project on my old holden shed.

Project: Rocker Cover facelift

After the success of the wiper facelift, I decided that things needed improving under the bonnet.

Check out the photo below, and you'll see what I mean:

So, I set to work with a few simple tools, and spruced up the rocker covers. While I was at it, i painted the snorkel - because I could:


If you want to see the full details of the project click here to open the project in my old holden shed. All the instructions are provided to do the job.

Project: Adding sill moulds

I've been on the hunt for some sill moulds which will fit along the bottom of the van.

What are they? The photo below shows the moulds as fitted to a Premier station wagon (they were standard on the Prem wagon). They are the chrome strips underneath the doors:


Sill moulds were also fitted to Statesmans - however for a panel van you need to get the wagon versions, as the Statesman moulds are about 6 inches shorter than the wagon versions. For a panel van, you need moulds which are 2080mm in length!

I bought a pair of moulds off eBay (again!) for about $75, and it cost me another $25 to have them freighted via TNT, as they were too long for Aussie Post:


After they were installed:

Click here to see the full details of how they were installed.

Project: Hole repair

In a recent entry, you saw that I replaced the guard mounted aerial with a roof mounted job. Nice work, but it left a hole in the guard which needs to be repaired. As a temporary measure I installed a plug - ugly plus!


The repair job was a simple fill and paint, and the end result was pretty good.

Click here to see the full step by step details in my old holden shed.

Project: Chrome Door Trim

At the All Holden Day in 2006, I spotted a van which had some nice chrome door trims from Statesman. I took a picture at the time, and I've included it below:


After watching eBay for a while, I snagged a set in good condition for around $40.

Before and After Pictures:

Click here to see the full project details, including more pictures.

There's more to the story - turns out I met the owner of the van (Leigh) at a van get together in Warrnambool. Check the pictures of the All Holden Day here, and have a look at the interior of the van. Wild!

Project: Knob Update

You know - I never really thought that the gear shift know installed on the old Aussie 4 speed really suited the van, so I decided to make a change.

Check the black/brown shroud. That needs to be changed too!

I hunted around some of the Auto parts stores, and found a SAAS timber look knob which matches the SAAS wheel.

Installation is a simple job, and you can click here to see the full project in my old holden shed.

I'm sure you will agree that it was a job worth doing!

Project: Roof mounted aerial

One of the things I've always liked on HQ-WB Holden is the roof mounted aerial. So I decided the time was right. A couple of hours and the job was done.

This aerial I bought at one of the auto parts stores (can't actually remember which one!) for under $20.

I'm pleased with the end result, especially as the aerial it replaced was one of those guard mounted extendable jobs, with the spring at the base.

To see the full detail of the project (including lots of pictures) click here to open the project in my old holden shed.


You can probably just make out the temporary plug I put in the guard. Repairing the hole is Whole other project!

Project: Wiper facelift

Time for the first project on the van. One of the things that was very obvious from the day I picked the Panel Van up was that the wiper arms were in need of some work.

Check the original photo below:


Like I said - obvious! So I set about cleaning them up and repainting them.

The after shot:


If you want the step by step instructions as to how it was done, or just want to know how to remove the wiper arms click here to see the whole project in my oldholden shed.

I was very happy with the result, and it cost bugger all!